MODE:
Press
"MODE" to change the difference mode in the following sequence:
TIMEKEEPING ALARMTIMER(StopWatch)
 _________________________________ |
TO
SET TIME AND DATE: (Timekeeping Mode, TV/VCR
off)
1.Use "MODE" to enter the time keeping mode. (Note
cannot set time & date from TV/VCR mode.
2. Hold down "SET" 3
seconds until the Seconds digit starts flash on display
While
the seconds digits are Selected (flashing), Press 
to Reset the seconds to "00"
3.
Press "MODE" to change the selection in the following sequence:
SECOND
HOUR MINUTE
MONTH DATE DAY
OF WEEK
______________________________________________________________
4. While selection is flashing Press "SELECT"
to switch For 12 hr and 24 hr format.
5.
While any digits (besides seconds) are selected (flashing), Press
to
set/adjust.
6.
After setting the Time and Date, Press "SET" again to return to
Time mode. |
TO
USE THE TV AND VCR REMOTE CONTROL FUNCTIONS:
1.While in Timekeeping mode, Press
"SELECT" to select either TV mode or VCR (Video) mode.
2.Hold
down "SET" 3 seconds until a manufacturers name appears flashing
on display.
3.While
TV or VCR manufacturer name-setting display is shown, Press
to
find the correct TV or VCR manufacturer-Name & Code. (to
Test whether or not
the displayed manufacturer Name & Code are correct for
your equipment,
Point
the signal emitter (Red Window) at your TV or VCR and press
"POWER" button
a) If the above operation switches the power ON/OFF of your TV/VCR,
It means that the correct code has been selected.
b) Certain TV and VCR may be slow to respond after receiving a
remote control signal
with such units, Try holding down "POWER" for one or two
seconds.
c) If nothing happens when you press "POWER", Use steps 3
to try for another code.
4.After
you set the correct manufacturer Name & Code, Press "SET" to
return to TV or VCR mode. |
| BUTTON
DESCRIPTION IN TV/VCR MODE: |
| Buttons |
Functions |
|
Increases
/ Decreases volume or Code. |
 |
Channel
Enter (TV Mode) |
 |
Switches
power ON & OFF. |
| CH+ |
Change
to next higher channel |
| CH- |
Change
to next lower channel |
| 0
- 9 |
For
channel selection (TV Mode) |
| 1
(REW) |
Starts
Rewind operation (VCR Mode). |
| 2
(STOP) |
Stops
tape transport (VCR Mode). |
| 3
(PLAY) |
Starts
Tape Playback (VCR Mode). |
| 4
(FF) |
Starts
fast forward operation (VCR Mode). |
|
COMPATIBLE
WITH FOLLOWING MANUFACTURERS` PRODUCTS:
| TV |
MODEL
(CODE) |
|
VCR |
MODEL
(CODE) |
| FERGUSON |
'01,02 |
|
AKAI |
'01,02,03 |
| FUNAI |
'01,02,03,04 |
|
FERGUSAN |
'01,02 |
| GOLDSTAR |
'01,02,03,04 |
|
FUNAI |
'01 |
| GRUNDIG |
'01,02,03 |
|
GOLDSTAR |
'01 |
| HITACHI |
'01,02,03,04,05,06 |
|
GRUNDIG |
'01,02,03 |
| JVC |
'01,02,03,04 |
|
HITACHI |
'01,02,03 |
| MITSUBISHI |
'01,02 |
|
JVC |
'01,02,03 |
| NEC |
'01,02,03,04 |
|
MITSUBISHI |
'01,02,03 |
| PANASONIC |
'01,02,03,04 |
|
NEC |
'01,02 |
| PHILIPS |
'01,02 |
|
NOKIA |
'01 |
| PIONEER |
'01 |
|
PANASONIC |
'01,02 |
| SAMSUNG |
'01,02,03,04,05,06 |
|
PHILIPS |
'01,02,03,04 |
| SANYO |
'01,02,03,04 |
|
PIONEER |
'01 |
| SHARP |
'01,02,03 |
|
SAMSUNG |
'01,02,03 |
| SONY |
'01,02 |
|
SANYO |
'01,02,03,04,05 |
| TELEFUNKEN |
'01,02 |
|
SHARP |
'01 |
| TOSHIBA |
'01,02,03,04 |
|
SONY |
'01,02,03 |
| |
|
|
TELEFUNKEN |
'01,02 |
| |
|
|
TOSHIBA |
'01,02,03 |
|
Some
TV or Tape Deck models may not work properly with this watch, even
though they are made by one of the manufacturers in the
manufacturers
code table.
Also you may find that you can control a TV or Tape deck using a code for a manufacturer that is different
from
the ones in the table. There
are some manufacturers with more than one code, Try the various codes
available for your equipment to find the one that works best. |
You
have to set separate codes for your TV and VCR even if they are made
by the same manufacturer.
INPUTTING TWO DIGIT CHANNEL NUMBERS:
There are various systems being used for input of two digits channel
numbers with this watch,
You should use the system that is closest to the one employed by the
remote control unit that
comes with your TV or Video equipment.
Example:
a) If the remote control unit of your equipment allows input of two
digits, Hold Down "1" for
two or three seconds and then Press "2"
button of the watch.
b) If remote control unit of your equipment uses an execute or confirm
button for two digits
channel number input. Press "1"
button and then the "2" and
then press ""
button of this watch. |
ALARM
MODE:
1. To set the Alarm time, Use "MODE"
to enter the alarm mode.
2. Hold
down "SET" 3 seconds until the minutes digit start flash on
display.
3.
Press "MODE" to change the selection in following sequence:
MINUTE
 HOUR
4.
While the digits are selected, Press
to
adjust alarm time.
5.
After setting the Alarm, Press "SET" again to return to Alarm
mode.
6.
Press "SELECT" while in
alarm mode to change the of the Daily alarm ON or OFF. |
TIMER-(StopWatch)
1. "SELECT" button switch Timer START / STOP (Maximum 23hours
59minutes 59seconds).
2. "SET" button
(a) Switch split Time mode ON/OFF while Timer start.
(b) Switch reset Timer (00) while timer stop. |
BATTERY:
Replacing
the battery will cause the remote control data setting (TV/VIDEO
Manufacturer Codes)
to be altered. Be
sure that you a note of your codes before you replace the battery.
Battery CR2032 to be used for this watch. |
|
|
Back
to Service page
To top |
|
|
